取消
中埋式651型橡胶止水带价格

中埋式651型橡胶止水带价格

衡水明兴工程橡胶有限公司
所在地:河北 衡水
最新产品 进入店铺
  • 详情
  • 联系方式

中埋式651型橡胶止水带价格

一、651型橡胶止水带简介:

Brief introduction of rubber seals of type 1 and 651:

651型止水带是止水带的一种常用型号,属于中埋式止水带,中心孔两侧各有3个突起的楞,具体型式请见图,而651型橡胶止水带又是止水带产品里使用***广泛的,常用的中埋式止水带还有652型、653型等。

The 651 type sealing strip is a common type of sealing strip, belonging to medium buried waterstop, the center hole of each of the 3 sides of the protruding arris, the specific type is shown in Figure 651, type rubber sealing strip is the most widely used products in the waterstop, commonly used in buried waterstop type, and 652 type 653.

二、651型止水带安装:

Installation of two and 651 type water stop belt:

在施工中,在混凝土浇注过程式中把橡胶止水带部分或全部浇埋在混凝土中,如果混凝土中有许多尖角的石子和锐利的钢筋头,由于橡胶的撕裂强度比拉伸强低3-5倍,因此一旦被刺破或撕裂时,不需很大外外力裂口就会扩大,所以在止水带定位和混凝土浇捣过程中,应注意定位方法和浇捣压力,以免止水带被刺破,所以在止水带定位和混凝土浇捣过程中,应注意定位方法和浇捣压力,以免被刺破,影响止水带的防水效果,具体注意事项如下:

In construction, the rubber sealing strip of all or part of pouring buried in concrete in concrete pouring process, if there are many sharp stones and sharp head reinforced concrete, the tear strength of rubber and low tensile 3-5 times, so once punctured or torn, without external force will be. To expand, so in the waterstop positioning and concrete pouring process, should pay attention to positioning method and pouring pressure, so as to avoid the water stop was punctured, so in the waterstop positioning and concrete pouring process, should pay attention to positioning method and pouring pressure, so as not to be punctured, affect the waterproof effect of waterstop, specific matters needing attention the following:

A、橡胶止水带不能长时间露天曝晒,防止雨淋,勿与污染性强的化学物质接触。产品应存放场所保持-10℃-+30℃,相对湿度在40%-80%。

A, rubber sealing tape can not be exposed for a long time in the open air, to prevent rain, do not contact with polluting chemicals. The product should be stored to keep the best places for -10 +30 C C, relative humidity in 40%80%.

B、在产品的运输和施工中,防止机械,钢筋损伤。成品存放和运输中应取直平放,勿加重压。

B, in the transport and construction of products, to prevent mechanical, steel damage. In the storage and transportation of the finished product, it should be taken straight and flat, without heavy pressure.

C、在施工过程中,产品安装必须固定,避免在浇注混凝土时发生位移,保证止水带在混凝土中的正确位置。

C, in the process of construction, product installation must be fixed, to avoid displacement when pouring concrete, to ensure the correct position of water stop in concrete.

D、通常我们固定止水带的方法有:利用附加钢筋固定;专用卡具固定;铅丝和模板固定等,如需穿孔时,只能选在止水带的边缘安装区,不得损伤其它部分。

D, we usually fixed strip methods are: the use of additional reinforcement fixation; special fixture fixed; the wire and the fixed template, such as perforation, can only choose the installation area on the strip edge, not to damage other parts.

E、用户定货时应根据工程结构,设计图纸计算好产品长度,异型结构要有图纸说明,尽量在工厂中将止水带连接成整体,如需在现场连接时,可采用电加热板硫化粘合或冷粘接(橡胶止水带)或焊接(塑料止水带)的方法,如用户连接有困难,我公司可派技术人员现场指导。

E, the user order should be based on the engineering structure design drawings, calculate the length of products, have special structure drawings and specifications, try to connect into a whole band in the factory will stop, if necessary in the field of connection, can use electric heating plate vulcanization bonding or cold bonding (rubber waterstop) or welding (plastic waterstop). Methods, such as the user is connected with the difficulties, our company can send technical personnel on-site guidance.

三、止水带分类:

Three. Classification of water stop belt:

止水带系采用弹性材料,并掺加多种辅加助剂,经混炼、硫化而制成。

The water stop belt is made of elastic material and mixed with a variety of auxiliary additives, and is made by mixing and vulcanizing.

根据产品选用材质的不同可分为天然橡胶止水带 氯丁橡胶止水带 丁腈橡胶止水带 三元乙丙橡胶止水带 塑料(PVC)止水带 止水带接头。

According to the choice of material, the product can be divided into natural rubber water stop belt, chloroprene rubber water stop belt, nitrile rubber waterproof belt, three ethylene propylene rubber water stop belt plastic (PVC) water stop belt and water stop joint.

根据结构形式的不同又可分为:CB型橡胶止水带 CP型橡胶止水带 EB型橡胶止水带 EP型橡胶止水带。

According to the structure of the different forms can be divided into: CB rubber sealing tape, CP rubber water stop belt, EB rubber water stop belt, EP type rubber water stop belt.

根据使用安装方式的不同可分为:中埋式止水带、外贴式止水带、可卸式止水

According to the different installation methods, it can be divided into the embedded water stop belt, the external sticking type water stop belt and the detachable water seal

四、

Four,


中埋式651型橡胶止水带价格

从材料选择来区分可分为中埋式651型橡胶止水带、中埋式PVC止水带、中埋式止水带接头和中埋式遇水膨胀止水带等。

From the choice of materials, it can be divided into embedded 651 type rubber water stop belt, embedded PVC water stop belt, middle buried water stop joint and embedded water expansion water stop belt, etc..

从结构形式上可分为CB型止水带和CP型止水带两种。

The structure can be divided into two types: CB type water stop belt and CP type water stop belt.

设计及选用标准: 在工程设计及施工选用过程中,CB型止水带的宽度及厚度应按以下条件确定

Design and selection criteria: in the process of engineering design and construction selection, the width and thickness of CB type water stop belt should be determined according to the following conditions

1、水压小于4m,水平和垂直变形量不超过10mm 时,止水带的宽度不宜小于200mm,厚度不宜小于5mm;

1, the water pressure is less than 4m, the horizontal and vertical deformation is not more than 10mm, the width of the water stop should not be less than 200mm, the thickness should not be less than 5mm;

2、水压为4-8m,水平和垂直变形量不超过30mm时,CB型止水带的宽度不宜小于300mm,厚度不宜小于6mm;

2, the water pressure is 4-8M, the horizontal and vertical deformation amount is not more than 30mm, the width of CB type water stop belt should not be less than 300mm, the thickness should not be less than 6mm;

3、水压大于8m,水平和垂直变形量超过30mm时,CB型止水带的宽度不宜小于350mm ,厚度不宜小于8mm;

3, the water pressure is greater than 8m, the horizontal and vertical deformation exceeds 30mm, the width of CB type water stop should not be less than 350mm, the thickness should not be less than 8mm;

4、水压不大于8m,水平变形量不超过20mm,当无垂直变形时,CB型止水带的宽度不宜小于200mm,厚度不宜小于5mm。除此之外,当结构断面尺寸大于500mm时,CB型止水带的宽度不宜小于300mm,当CB型止水带进行弯曲放置时,其转弯半径不得小于300mm。

4, the water pressure is not greater than 8m, the horizontal deformation is not more than 20mm, when there is no vertical deformation, the width of CB type water stop should not be less than 200mm, the thickness should not be less than 5mm. In addition, when the section size of the structure is greater than 500mm, the width of CB type water stop belt should not be less than 300mm, and when the CB type water stop strip is bent, the turning radius of the 300mm type water stop band shall not be less than 20 mm.


以上为"中埋式651型橡胶止水带价格"供应信息
相关推荐
产品分类 更多 >
新品速递 查看更多 >
中国供应商> 橡胶带> 橡胶止水带> 中埋式651型橡胶止水带价格