取消
供应医疗级PC,基础创新HP1 生物相容性 过ISO10993 USP Class VI

供应医疗级PC,基础创新HP1 生物相容性 过ISO10993 USP Class VI

东莞市宇峰塑胶化工有限公司
所在地:广东 东莞
最新产品 进入店铺
  • 详情
  • 联系方式


LEXAN™ HOMOPOLYMER

HP1

REGION AMERICAS

DESCRIPTION

High flow polycarbonate. For medical devices and pharmaceutical applications. Healthcare management of change,

biocompatible (ISO10993 or USP Class VI). EtO sterilizable. Contains mold release.

TYPICAL PROPERTY VALUES

PROPERTIES TYPICAL VALUES UNITS TEST METHODS

MECHANICAL

Tensile Stress, yld, Type I, 50 mm/min 62 MPa ASTM D 638

Tensile Stress, brk, Type I, 50 mm/min 65 MPa ASTM D 638

Tensile Strain, yld, Type I, 50 mm/min 6 % ASTM D 638

Tensile Strain, brk, Type I, 50 mm/min 120 % ASTM D 638

Tensile Modulus, 50 mm/min 2370 MPa ASTM D 638

Flexural Stress, yld, 1.3 mm/min, 50 mm span 93 MPa ASTM D 790

Flexural Modulus, 1.3 mm/min, 50 mm span 2300 MPa ASTM D 790

Hardness, Rockwell M 70 - ASTM D 785

Hardness, Rockwell R 118 - ASTM D 785

Taber Abrasion, CS-17, 1 kg 10 mg/1000cy ASTM D 1044

Tensile Stress, yield, 50 mm/min 63 MPa ISO 527

Tensile Stress, break, 50 mm/min 50 MPa ISO 527

Tensile Strain, yield, 50 mm/min 6 % ISO 527

Tensile Strain, break, 50 mm/min 70 % ISO 527

Tensile Modulus, 1 mm/min 2350 MPa ISO 527

Flexural Stress, yield, 2 mm/min 90 MPa ISO 178

Flexural Modulus, 2 mm/min 2300 MPa ISO 178

IMPACT

Izod Impact, unnotched, 23°C 3204 J/m ASTM D 4812

Izod Impact, notched, 23°C 640 J/m ASTM D 256

Izod Impact, notched (natural, tints) 640 J/m ASTM D 256

Tensile Impact, Type S 378 kJ/m² ASTM D 1822

Falling Dart Impact (D 3029), 23°C 169 J ASTM D 3029

Instrumented Impact Energy @ peak, 23°C 54 J ASTM D 3763

© 2017 Copyright by SABIC. All rights reserved

Izod Impact, unnotched 80*10*4 +23°C NA kJ/m² ISO 180/1U

Izod Impact, unnotched 80*10*4 -30°C NA kJ/m² ISO 180/1U

Izod Impact, notched 80*10*4 +23°C 12 kJ/m² ISO 180/1A

Izod Impact, notched 80*10*4 -30°C 10 kJ/m² ISO 180/1A

Charpy 23°C, V-notch Edgew 80*10*4 sp=62mm 12 kJ/m² ISO 179/1eA

Charpy -30°C, V-notch Edgew 80*10*4 sp=62mm 10 kJ/m² ISO 179/1eA

THERMAL

HDT, 1.82 MPa, 3.2mm, unannealed 126 °C ASTM D 648

HDT, 0.45 MPa, 6.4 mm, unannealed 137 °C ASTM D 648

HDT, 1.82 MPa, 6.4 mm, unannealed 126 °C ASTM D 648

CTE, -40°C to 95°C, flow 6.84E-05 1/°C ASTM E 831

Specific Heat 1.25 J/g-°C ASTM C 351

Thermal Conductivity 0.19 W/m-°C ASTM C177

Thermal Conductivity 0.2 W/m-°C ISO 8302

CTE, 23°C to 80°C, flow 7.E-05 1/°C ISO 11359-2

Ball Pressure Test, 125°C +/- 2°C PASSES - IEC 60695-10-2

Vicat Softening Temp, Rate B/50 139 °C ISO 306

Vicat Softening Temp, Rate B/120 140 °C ISO 306

HDT/Be, 0.45MPa Edgew 120*10*4 sp=100mm 133 °C ISO 75/Be

HDT/Ae, 1.8 MPa Edgew 120*10*4 sp=100mm 121 °C ISO 75/Ae

Relative Temp Index, Elec 130 °C UL 746B

Relative Temp Index, Mech w/impact 130 °C UL 746B

Relative Temp Index, Mech w/o impact 130 °C UL 746B

PHYSICAL

Specific Gravity 1.2 - ASTM D 792

Specific Volume 0.83 cm³/g ASTM D 792

Density 1.19 g/cm³ ASTM D 792

Water Absorption, 24 hours 0.15 % ASTM D 570

Water Absorption, equilibrium, 23C 0.35 % ASTM D 570

Water Absorption, equilibrium, 100°C 0.58 % ASTM D 570

Mold Shrinkage, flow, 3.2 mm (5) 0.5 – 0.7 % SABIC method

Melt Flow Rate, 300°C/1.2 kgf 25 g/10 min ASTM D 1238

Melt Volume Rate, MVR at 300°C/1.2 kg 23 cm³/10 min ISO 1133

OPTICAL

Light Transmission, 2.54 mm 88 % ASTM D 1003

Haze, 2.54 mm 1 % ASTM D 1003

Refractive Index 1.586 - ASTM D542

ELECTRICAL

PROPERTIES TYPICAL VALUES UNITS TEST METHODS

© 2017 Copyright by SABIC. All rights reserved

Volume Resistivity >1.E+17 Ohm-cm ASTM D 257

Dielectric Strength, in air, 3.2 mm 14.9 kV/mm ASTM D 149

Relative Permittivity, 50/60 Hz 3.17 - ASTM D 150

Relative Permittivity, 1 MHz 2.96 - ASTM D 150

Dissipation Factor, 50/60 Hz 0.0009 - ASTM D 150

Dissipation Factor, 1 MHz 0.01 - ASTM D 150

Hot Wire Ignition {PLC) 2 PLC Code UL 746A

High Voltage Arc Track Rate {PLC} 2 PLC Code UL 746A

High Ampere Arc Ign, surface {PLC} 1 PLC Code UL 746A

Comparative Tracking Index (UL) {PLC} 2 PLC Code UL 746A

Volume Resistivity >1.E+15 Ohm-cm IEC 60093

Surface Resistivity, ROA >1.E+15 Ohm IEC 60093

Dielectric Strength, in oil, 3.2 mm 17 kV/mm IEC 60243-1

Relative Permittivity, 1 MHz 2.7 - IEC 60250

Dissipation Factor, 50/60 Hz 0.001 - IEC 60250

Dissipation Factor, 1 MHz 0.01 - IEC 60250

Relative Permittivity, 50/60 Hz 2.7 - IEC 60250

FLAME CHARACTERISTICS

UL Recognized, 94V-2 Flame Class Rating (3) 1.09 mm UL 94

Oxygen Index (LOI) 25 % ISO 4589

INJECTION MOLDING

Drying Temperature 120 °C

Drying Time 3 – 4 hrs

Drying Time (Cumulative) 48 hrs

Maximum Moisture Content 0.02 %

Melt Temperature 270 – 295 °C

Nozzle Temperature 265 – 290 °C

Front - Zone 3 Temperature 270 – 295 °C

Middle - Zone 2 Temperature 260 – 280 °C

Rear - Zone 1 Temperature 250 – 270 °C

Mold Temperature 70 – 95 °C

Back Pressure 0.3 – 0.7 MPa

Screw Speed 40 – 70 rpm

Shot to Cylinder Size 40 – 60 %

Vent Depth 0.025 – 0.076 mm

PROPERTIES TYPICAL VALUES UNITS TEST METHODS

© 2017 Copyright by SABIC. All rights reserved

DESCRIPTION

TBD

DISCLAIMER

Any sale by SABIC, its subsidiaries and affiliates (each a “seller”), is made exclusively under seller’s standard conditions of sale

(available upon request) unless agreed otherwise in writing and signed on behalf of the seller. While the information contained herein

is given in good faith, SELLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY AND

NONINFRINGEMENT OF INTELLECTUAL PROPERTY, NOR ASSUMES ANY LIABILITY, DIRECT OR INDIRECT, WITH RESPECT

TO THE PERFORMANCE, SUITABILITY OR FITNESS FOR INTENDED USE OR PURPOSE OF THESE PRODUCTS IN ANY

APPLICATION. Each customer must determine the suitability of seller materials for the customer’s particular use through appropriate

testing and analysis. No statement by seller concerning a possible use of any product, service or design is intended, or should be

construed, to grant any license under any patent or other intellectual property right.


以上为"供应医疗级PC,基础创新HP1 生物相容性 过ISO10993 USP Class VI"供应信息
相关推荐
产品分类 更多 >
新品速递 查看更多 >
中国供应商> 工程塑料> PC> 供应医疗级PC,基础创新HP1 生物相容性 过ISO10993 USP Class VI